I-hand drill yinto efanelekileyo, kulula ukuyiphathaI-CORDLES SCREW DRIVER DZ-LS1002/12Visixhobo, kwaye siquka injini encinci, iswitshi yokulawula, i-drill chuck kunye ne-drill bit.Ukuze usebenzise esi sixhobo kakuhle, akudingeki ukuba uqonde imigangatho yokusebenza kwayo, kodwa kufuneka uqonde izilumkiso zesicelo, kwaye ukusebenza okungalunganga kuya kwenza ilahleko.Landela umhleli ongezantsi ukuze ufunde malunga nezilumkiso kunye nemigangatho yokusebenza yokusetyenziswa kwezixhobo zombane.

uMgangatho wokuSebenza:

1. I-casing ye-drill hand drill isekelwe okanye ixhunywe kumgca ongathathi hlangothi wokugcinwa.

2. Ucingo lwe-drill yesandla kufuneka lugcinwe kakuhle ukukhusela ucingo ukuba lungonakaliswe okanye lunqunywe ngokutsalwa okungahleliwe.Akuvumelekanga ukutsala ucingo emanzini aneoli, kwaye amanzi anamafutha aya kutshabalalisa ucingo.

3. Nxiba iiglavu zerabha kunye nezihlangu zerabha xa uyisebenzisa;xa usebenza kwiindawo ezimanzi zengingqi, yima phezu kweerabha okanye iibhodi zamaplanga ezi monotonous ukukhusela ukutshitshiswa kombane.

4. Xa i-drill yombane ifunyenwe ivuza, ingcangcazela, ukushisa okuphezulu okanye ingxolo engaqhelekanga ngexesha lokusetyenziswa, kufuneka isebenze ngokuqhubekayo kwaye ifumane ingcali yombane ukuba ikhangele kwaye ilungise.

5. Xa i-drill drill ingaqhubeki ngokuqhubekayo, i-drill bit ayikwazi ukuthululwa okanye ukutshintshwa.Umbane kufuneka ucinywe xa ukucima kombane kuphumle okanye ushiye indawo yokusebenza.

6. Ayinakusetyenziselwa ukugaya i-samente kunye neendonga zezitena.Ngaphandle koko, kulula ukwenza ukuba i-motor ilayishe kakhulu kwaye itshise i-motor.Undoqo ulele ekunqongophelweni kombutho wempembelelo kwi-motor, kwaye amandla okuthwala amancinci.

Sebenzisa isilumkiso:

1. Iikhrayitheriya zokukhetha.Ngokubhekiselele kwii-diameters ezahlukeneyo zokugaya, umgangatho ohambelanayo wokugaya umbane kufuneka ukhethwe ngokusemandleni.

2. Qaphela ukuba i-voltage kufuneka ihambelane.Xa udibanisa kunye nokunikezelwa kwamandla, qaphela ukuba ingaba i-voltage ye-voltage ihambelana ne-voltage elinganisiweyo ye-drill yombane.

3. Jonga ukuxhathisa edge.Ukuqhuba umbane okanye iidrill zombane ezintsha ezingafunekiyo ixesha elide, sebenzisa i-500V imitha yokumelana ne-insulation ukulinganisa ukunyanzeliswa kwe-insulation phakathi kokujija kunye ne-casing ngaphambi kokusetyenziswa.Ukuchasana akufanele kube ngaphantsi kwe-0.5Mf, ngaphandle koko kufuneka kube monotonic.

4. Ukugrumba.I-drill bit esetyenzisiweyo ibukhali, musa ukusebenzisa amandla amaninzi xa ubhobhoza, kwaye i-drill drill igcwele kakhulu.Xa isantya siyehla ngokukhawuleza.Ukuba i-drill yombane iyayeka ngokukhawuleza, umbane kufuneka unqunyulwe.

5. Kufuneka kubekho ukugquma okukhuselekileyo.Jonga ukuba ngaba ucingo olusemhlabeni lugqwesile na phambi kokusetyenziswa.

6. Uvavanyo lwe-idling.Phambi kokusetyenziswa, kufuneka ibambe i-1min ukujonga ukuba umsebenzi wokuqhuba umbane uqhelekile.Xa i-drill yombane yesigaba sesithathu ivavanywa, kuyafuneka kwakhona ukujonga ukuba ngaba ukujikeleza kwe-drill shaft kuqhelekileyo.Ukuba i-steering ayilunganga, iingcingo zombane zesigaba sesithathu ze-drill drill zingatshintshwa ngokuthanda ukutshintsha i-steering.

7. Uqhelaniso oluchanekileyo.Xa uhambisa i-drill drill, ubambe umqheba we-drill yombane, ungalibazisi intambo yamandla ukuhambisa i-drill yombane, kwaye intambo yamandla inokukrweleka okanye icunyuzwe.

8. I-drill yombane kufuneka iphathwe ngokulula emva kokusetyenziswa.Umonakalo kwi-casing okanye ezinye iindawo ngempembelelo.